[June-2019-New]100% Success-Braindump2go 642-887 Exam PDF Dumps 152Q Instant Download

June/2019 Braindump2go Cisco CCNP SP 642-887 SPCORE Dumps with PDF and VCE New Updated Today! Following are some new 642-887 Exam Questions:

1.|2019 Laetst 642-887 Exam Dumps (PDF & VCE) Instant Download:

https://www.braindump2go.com/642-887.html

2.|2019 Laetst 642-887 Exam Questions & Answers Instant Download:

New Question
Which four options describe the functions of the control world in an AToM environment? (Choose four.)

A. It carries generic and Layer 2 payload-specific information.
B. It prevents fragmentation and reassembly.
C. It preserves the sequence of the transported frames.
D. It is responsible for padding all packets.
E. It is responsible for padding the small packets.
F. It enables proper load balancing without packet desequencing independent of L2VPN packet content.
G. It enables an optimal path for the L2VPN packet content to follow through the MPLS backbone.
H. It carries Layer 2 payload-specific information.

Answer: ACEF

New Question
Referring to the Cisco IOS XR show command output exhibit, what are three possible reasons that the GigabitEthernet0/1/0/10 LDP IGP sync status is not ready? (Choose three.)

A. GigabitEthernet0/1/0/10 is not configured to run LDP.
B. Graceful restart is not configured on the peer.
C. The LDP neighbor on GigabitEthernet0/1/0/10 is not up.
D. The OSPF neighbor on GigabitEthernet0/1/0/10 is not up.
E. LDP is up on GigabitEthernet0/1/0/10, but no label bindings have been received from the peer.
F. GigabitEthernet0/1/0/10 is a member link of Bundle-Ether9000.

Answer: CDE

New Question
Refer to the exhibit. XR2 needs to have LDP configured with PE1.
Which configuration achieves this goal?

A. interface giga 0/0
Mpls ip
exit
commit
B. router ospf 1
mpls ldp auto config area 0
exit
commit
C. router ospf 1
area 0 mpls ldp auto config
exit
commit
D. interface giga 0/1
mpls ldp
exit
commit

Answer: C

New Question
Which three fields must be the same in an IPv6 header to consider different packets on the same flow? (Choose three.)

A. source port
B. destination address
C. destination port
D. source address
E. flow label
F. transport protocol type

Answer: BDE

New Question
An engineer is working in a service provider environment to troubleshoot a MPLS VPN. The engineer determines that LDP neighborship is flapping between two routers and causing disruption to the traffic. Which LDP feature can help to solve the issue?

A. LDP Discovery
B. LDP auto-configuration
C. LDP graceful-restart
D. LDP NSF

Answer: C

New Question
Which configuration can a network engineer use to establish high availability for LDP in an MPLS setup?

A. mpls ldp
graceful-restart
graceful-restart
graceful-restart forwarding state-holdtime 180
graceful-restart reconnect-timeout 15
interface HundredGigE0/4/0/0
B. mpls ldp
graceful-restart
graceful-restart forwarding state-holdtime 180
graceful-restart reconnect-timeout 15
C. mpls ldp
session protection for peer_acl duration 60
ipv4 access-list peer_acl
10 permit ip host 192.168.10.1 any
D. router ospf 1
mpls ldp sync
mpls ldp
igp sync delay 30
E. mpls ldp
router-id loopback0
discovery hello holdtime 15
discovery hello interval 5

Answer: A

New Question
Which configuration fulfills the requirement of configuring LDP with Cisco Nonstop Forwarding on a router with 5 minutes time to hold the forwarding table information and 1 minute retry timer value for an LDP connection?

A. mpls ldp
graceful-restart
graceful-restart forwarding state-holdtime 5
graceful-restart reconnect-timeout 1
interface GigabitEthernet0/0/0/0
!
B. mpls ldp
graceful-restart
graceful-restart forwarding state-holdtime 300
graceful-restart reconnect-timeout 60
interface GigabitEthernet0/0/0/0
!
C. mpls ldp
nsr
graceful-restart
graceful-restart forwarding state-holdtime 300
graceful-restart reconnect-timeout 60
interface GigabitEthernet0/0/0/0
!
D. mpls ldp
nsr
graceful-restart
graceful-restart forwarding state-holdtime 5
graceful-restart reconnect-timeout 1
interface GigabitEthernet0/0/0/0
!

Answer: B

New Question
Which three commands are used to troubleshoot why IP packets are not forwarded on the LSP? (Choose three.)

A. show cef prefix/length to check the prefix information
B. debug mpls ldp transport events to display events related to the LDP peer discovery mechanism
C. show mpls forwarding labels <label-id> hardware egress location <node-id> to check the hardware label FIB
D. show arp <prefix> location <node-id> for the next hop prefix
E. show mpls ldp discovery for the corresponding label information
F. debug mpls ea platform all to display MPLS setup events and errors

Answer: ACD

New Question
A network engineer must design a core network routing domain that supports Cisco MPLS TE. Which two interior gateway protocols represent viable solutions? (Choose two.)

A. Routing Information Protocol version 2
B. Open Shortest Path First
C. Enhanced Interior Gateway Routing Protocol
D. Intermediate-System to Intermediate-System
E. Border Gateway Protocol

Answer: BD

New Question
The network architecture team is proposing to enable Cisco MPLS TE over the entire service provider core network. Which two options are benefits of Cisco MPLS TE that affect their decision? (Choose two.)

A. Cisco MPLS TE optimizes network resources.
B. Cisco MPLS TE data flows independent from the underlying IGP.
C. Cisco MPLS TE increases the data forwarding rate.
D. Cisco MPLS TE tunneling does not require maintenance.
E. Cisco MPLS TE offers network resource reservation, which removes any need for QoS MQC policies.

Answer: AB

New Question
Which two fields are in the traffic engineering topology database? (Choose two.)

A. TE-metric
B. IGP metric
C. link delay
D. LSP setup priority
E. LDP authentication

1.|2019 Laetst 642-887 Exam Dumps (PDF & VCE) Instant Download:

https://www.braindump2go.com/642-887.html

2.|2019 Laetst 642-887 Study Guide Video Instant Download: