[Jul. 2016-NEW]Free Braindump2go 210-065 Questions Instant Download 192Q&As[NQ21-NQ30]
2016 July Cisco Official - 210-065:Implementing Cisco Video Network Devices (CIVND) Exam Questions New Updated Today in Braindump2go.com for Free Instant Download! 100% Exam Pass Guaranteed!
NEW QUESTION 21 - NEW QUESTION 30: 1.|2016 Latest Cisco 210-065 PDF Dumps & 210-065 VCE Dumps 192Q&As Instant Download: http://www.braindump2go.com/210-065.html [100% Exam Pass Promised!]
2.|2016 New Cisco 210-065 Exam Questions PDF - Google Drive:https://drive.google.com/folderview?id=0B272WrTALRHcRWU0dTZQQUpjMVU&usp=sharing QUESTION 21
Which CLI command can be used to reset the Cisco TelePresence System 500-32 personal video system to a factory condition? A. utils factory reset 2
B. utils system factory init
C. xcommand defaultvalues set level: 2
D. xconfiguration default factory
E. utils reset factory
F. xcommand SystemUnit FactoryReset Answer: B QUESTION 22
In this item, you will need to use all information presented to you to successfully answer the question.
The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network.
Based on the exhibits, what could be causing the issue?
 A. The subnet mask on the codec is incorrect.
B. The ip address of the codec is incorrect.
C. The interface that the codec is in is in the wrong VLAN.
D. The codec did not receive a DHCP address from the DHCP server. Answer: A
Explanation:
The subnet mask configured on the codec is 255.255.255.128, when it should be 255.255.255.0. QUESTION 23
Which three of these are functions of the Cisco TelePresence Management Suite? (Choose three.) A. automatic software update and release keys
B. intelligent call routing engine
C. provisioning a Cisco TelePresence System endpoint
D. tracing SIP and H.323 calls
E. managing phonebooks for endpoints that are registered to the Cisco Unified Cisco Unified Communications Manager
F. rebooting endpoints that are registered to the Cisco TelePresence Video Communications
Server Answer: ABF QUESTION 24
Refer to the exhibit. Which system tab can be used to add video infrastructure devices and endpoints?
 A. Navigator
B. System Overview
C. Configuration Templates
D. Provisioning
E. Administrative Tools Answer: A QUESTION 25
Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.) A. enhanced continuous presence
B. active speaker switching
C. continuous presence
D. speaker switching
E. room switching
F. active continuous presence Answer: DE QUESTION 26
Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time? A. enhanced continuous presence
B. active speaker
C. continuous presence
D. room switching
E. speaker switching Answer: A QUESTION 27
Which four features are provided by Cisco TelePresence Management Suite? (Choose four.) A. Scheduling of video conference calls
B. Built-in-bridge functionality for multiparty video conferences
C. SIP-H.323 protocol interworking
D. Centralized management of conference resources
E. SMTP email event notification
F. Endpoint configuration backup and restore
G. Cisco TelePresence endpoint automated redundancy
H. Automated resource optimization Answer: ADEF QUESTION 28
An important Cisco TelePresence video multipoint call is in progress and you are getting complaints of pixilation of the video and poor audio quality on one of the involved systems.
Which page would be a good place to start for troubleshooting the issue on the affected endpoint?
 A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D Answer: A QUESTION 29
Which two of these support an ad-hoc conference call? (Choose two.) A. Cisco TelePresence Multiway with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence Video Communications Server
B. using the Cisco TelePresence Management Suite Scheduler to schedule a conference call
to start in 5 minutes
C. using the Booking tab in the Cisco TelePresence Management Suite to configure a new conference
D. using the tab Administrative Tools > Configuration > Conference Settings in the Cisco TelePresence Management Suite
E. pressing the conference button on a Cisco Unified IP Phone 8941 to conference in a third
call Answer: AE QUESTION 30
Refer to the exhibit. Which configuration element can be used to specify the Multiway address that can be used by the endpoint to initiate Multiway calls?
 A. Conference 1
B. NetworkServices
C. Provisioning
D. SIP Profile 1
E. Video Answer: B
!!!! Recommend!!!! Braindump2go 2016 Jul. New Updated 210-065 Exam PDF and VCE 192Q Dumps: http://www.braindump2go.com/210-065.html [100% Exam Pass Guaranteed!] 210-065 Exam Google Drive: 1.Cisco 210-065 Exam VCE and PDF Dumps Download: https://drive.google.com/folderview?id=0B272WrTALRHcdkRINUNIR1h2Ums&usp=sharing
2.New 210-065 Exam Dumps and 210-065 Exam Questions 192Q&As: https://drive.google.com/folderview?id=0B272WrTALRHcVlhYdTdDeUdWQVE&usp=sharing
|