Braindump2go Free Exam Dumps with PDF and VCE Collection
https://www.mcitpdump.com/300-115-new-dumpsfull-version-300-115-dumps-pdf-and-vce-358q-for-free-download111-115.html
Export date: Fri Nov 22 1:29:08 2024 / +0000 GMT

[300-115 New Dumps]Full Version 300-115 Dumps PDF and VCE 358Q for Free Download[111-115]


2017 June New Updated Cisco 300-115 Exam Dumps with PDF and VCE Free Version from www.Braindump2go.com
100% Real Exam Questions! 100% Exam Pass Guaranteed!

1.|2017 Version New 300-115 PDF and 300-115 VCE 358Q&As Download:
http://www.braindump2go.com/300-115.html

2.|2017 Version New 300-115 Exam Questions & Answers Download:
https://drive.google.com/drive/folders/0B75b5xYLjSSNYjV4eHQ4dTJoQXc?usp=sharing

QUESTION 111
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
 
You are connecting the New_Switch to the LAN topology; the switch has been partially configured and you need to complete the rest of configuration to enable PC1 communication with PC2. Which of the configuration is correct?
 

A.    Option A
B.    Option B
C.    Option C
D.    Option D
E.    Option E

Answer: D
Explanation:
Within any VTP, the VTP domain name must match. So, step one is to find the correct VTP name on the other switches. Logging in to SW1 and using the "show vtp status" command we see this:
 
So we know that the VTP domain must be CCNP. This leaves only choice D and
E. We also see from the topology diagram that eth 0/0 of the new switch connects to a PC in VLNA 100, so we know that this port must be an access port in VLAN 100, leaving only choice D as correct. Note that the VTP versions supported in this network are 1, 2, 3 so either VTP version 2 or 3 can be configured on the new switch.

QUESTION 112
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
 
Refer to the configuration. For which configured VLAN are untagged frames sent over trunk between SW1 and SW2?

A.    VLAN1
B.    VLAN 99
C.    VLAN 999
D.    VLAN 40
E.    VLAN 50
F.    VLAN 200
G.    VLAN 300

Answer: B
Explanation:
The native VLAN is used for untagged frames sent along a trunk. By issuing the "show interface trunk" command on SW1 and SW2 we see the native VLAN is 99.
 
 

QUESTION 113
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
 
You are adding new VLANs. VLAN500 and VLAN600 to the topology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?

A.    Configure VLAN 500 & VLAN 600 on both SW1 & SW2
B.    Configure VLAN 500 and VLAN 600 on SW1 only
C.    Configure VLAN 500 and VLAN 600 on SW2 only
D.    Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4
E.    On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.

Answer: A
Explanation:
By issuing the "show vtp status command on SW2, SW2, and SW4 we see that both SW1 and SW2 are operating in VTP server mode, but SW4 is a client, so we will need to add both VLANs to SW1 and SW2.
 
 
 

QUESTION 114
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.
 
Examine the VTP configuration. You are required to configure private VLANs for a new server deployment connecting to the SW4 switch. Which of the following configuration steps will allow creating private VLANs?

A.    Disable VTP pruning on SW1 only
B.    Disable VTP pruning on SW2 only
C.    Disable VTP pruning on SW4 only
D.    Disable VTP pruning on SW2, SW4 and New_Switch
E.    Disable VTP pruning on New_Switch and SW4 only.

Answer: C
Explanation:
To create private VLANs, you will need to only disable pruning on the switch that contains the private VLANs. In this case, only SW4 will connect to servers in a private VLAN.

QUESTION 115
Drag and Drop Question
 
Answer:
 


!!!RECOMMEND!!!

1.|2017 Version New 300-115 PDF and 300-115 VCE 358Q&As Download:
http://www.braindump2go.com/300-115.html

2.|2017 Version New 300-115 Study Guide Video:

YouTube Video: YouTube.com/watch?v=MZAJaMB2e9k 1

Links:
  1. http://www.youtube.com/watch?v=MZAJaMB2e9k
Post date: 2017-06-07 03:35:24
Post date GMT: 2017-06-07 03:35:24

Post modified date: 2017-06-07 03:35:24
Post modified date GMT: 2017-06-07 03:35:24

Export date: Fri Nov 22 1:29:08 2024 / +0000 GMT
This page was exported from Braindump2go Free Exam Dumps with PDF and VCE Collection [ https://www.mcitpdump.com ]
Export of Post and Page has been powered by [ Universal Post Manager ] plugin from www.ProfProjects.com